Do I need a conductive substrate for electronic integrity testing?

Yes. Both low-voltage wet testing and high-voltage dry testing require a conductive substrate directly below the waterproofing membrane — typically a concrete or metal deck. On timber decks, a conductive medium such as wire mesh or conductive glass felt can be installed during construction to enable EIT. See LRWA Guidance Note 18 (2025) for full substrate requirements.

Can you electronically test a green roof or buried waterproofing?

Not with standard EIT once the overburden is in place. For buried waterproofing, the correct method is electrical field mapping (EFM) — a buried leak location technique that locates membrane breaches to within approximately one metre without lifting the overburden. CIRIA C817 and the GRO Green Roof Code both recognise EIT as a pre-covering QA method and EFM as the post-burial investigation method.

What is the difference between moisture mapping and leak detection?

Moisture mapping tells you where moisture has accumulated within the roof build-up. It does not tell you where the membrane has failed. Leak detection methods such as low-voltage EIT or electrical field mapping locate the actual breach in the membrane. The two are complementary: moisture mapping identifies which areas need investigation; breach-location methods find the source.

Is flood testing safe for flat roofs?

Flood testing carries real risks. A 150mm head of water adds approximately 150kg per square metre of loading — structural sign-off is essential. Water can take many hours to manifest internally, making short test periods unreliable. Flood testing can also cause structural deflection that opens up laps and details. It has a legitimate role in post-repair verification of specific, structurally appropriate areas only.

What qualifications should a roof leak detection specialist hold?

Look for: NVQ Level 3 in waterproofing testing and inspection; RAWTA membership (the Roofing and Waterproofing Test Association); and a demonstrable CV in flat roofing and waterproofing systems. Under the Building Safety Act 2022, appointing an incompetent inspector carries legal liability for duty holders.

Which leak detection method works on a single ply membrane?

For QA of weld continuity at laps and details, vacuum box testing is most reliable. For field-sheet investigation with a conductive substrate, low-voltage wet EIT is standard. High-voltage dry testing also works on non-conductive single ply on conductive substrates. Black EPDM membranes are generally not suitable for EIT due to carbon black content.

How does permanent sensor monitoring differ from leak detection surveys?

Leak detection surveys are point-in-time investigations locating a breach. Permanent sensor monitoring is continuous infrastructure embedded during construction, monitoring moisture in real time and triggering automated alerts. CIRIA C817 specifies permanent monitoring for blue-green roofs; BS 6229:2025 references electronic devices for detecting leaks between inspections.

Does electronic leak detection work in the rain?

Low-voltage wet testing requires a wet surface so rain is not a problem. High-voltage dry testing requires a dry membrane and cannot be performed in wet conditions. Tramex capacitance mapping works in most weather. Infrared thermography requires dry sunny conditions. Tracer gas is best in calm dry conditions as wind disperses escaping gas.

Ben Hickman - Vector

Waterproofing QA — The Step Everyone Skips

Post author:Ben Hickman
Post published:March 26, 2026
Post category:Technical Insights

Waterproofing QA testing is the gap between good design and buildings that actually stay dry. Learn why it's essential, what it costs to skip it, and how Vector's commissioning service protects all parties.

Data Centre Roof Monitoring — Why Sensors Are Non-Negotiable

Post author:Ben Hickman
Post published:March 26, 2026
Post category:Technical Insights

Data centre roof leaks cost £500k+ in downtime. Why sensor monitoring is non-negotiable, how Vector's three-phase model works, and the Building Safety Act implications.

Electronic Leak Detection — The Complete UK Guide

Post author:Ben Hickman
Post published:March 26, 2026
Post category:Technical Insights

Electronic leak detection replaced flood testing as the UK standard for waterproofing verification. Learn which method—HVELD or LVELD—suits your project, what standards apply, and how to specify it correctly.